|
9/6/2005 |
Ordered fuselage kit |
|
11/9/2005 |
Fuselage kit arrived |
4.0 |
|
12/7/2005 |
Started building the jig |
2.5 |
12/10/2005 |
More jig work |
2.0 |
|
12/11/2005 |
More or less finished with the jig |
3.0 |
12/13/2005 |
Finished inventorying. Started on firewall. |
2.5 |
|
12/14/2005 |
Drilled and deburred holes in firewall |
1.5 |
12/16/2005 |
Etched, Alodined and primed the firewall
parts. |
1.5 |
|
12/17/2005 |
Riveted on firewall parts |
1.5 |
12/18/2005 |
Drilled rudder cable hole |
1.0 |
|
12/19/2005 |
Made center section attachments |
2.5 |
12/20/2005 |
Riveted center section attachments |
1.5 |
|
12/21/2005 |
Misc center section tasks |
3.0 |
12/26/2005 |
Made seat belt fairleads and new temporary spars |
3.0 |
|
12/27/2005 |
Started deburring and fluting bulkhead parts |
1.0 |
12/28/2005 |
Finished deburring and fluting. Etched and Alodined bulkead parts. |
2.5 |
|
12/30/2005 |
Riveted two bulkheads |
1.5 |
12/31/2005 |
Put together bulkhead F-811 |
2.5 |
|
1/2/2006 |
Riveted aft-most bulkhead started on sub-floor |
1.0 |
1/3/2006 |
Drilled and beveled edges on rear spar attach |
1.0 |
|
1/4/2006 |
Prepared and primed rear spar attach and lateral bulkhead. |
1.5 |
1/5/2006 |
Bent, deburred, prep'ed and primed bulkhead gusset F-806FPP |
2.0 |
|
1/6/2006 |
Made F-805D |
1.0 |
1/7/2006 |
Made seat belt attach points |
1.5 |
|
1/8/2006 |
Worked on inner ribs in sub-floor |
3.5 |
1/12/2006 |
Drilled angle for mounting sub-floor to center section. |
2.0 |
|
1/13/2006 |
Mounted the firewall to the jig. |
2.0 |
1/14/2006 |
Finished sub-floor. Bent longerons. |
6.0 |
|
1/15/2006 |
Lined up jig and longerons. |
2.5 |
1/16/2006 |
Installed bulkheads in jig. |
3.5 |
|
1/18/2006 |
Rivet tacked center section rib doublers |
2.0 |
1/19/2006 |
Leveled the jig |
2.0 |
|
1/21/2006 |
Made and installed seat belt brackets |
1.5 |
2/3/2006 |
Drilled tail wheel mount. Primed longerons. |
2.0 |
|
2/4/2006 |
Drilled inside front bottom skin |
4.5 |
2/5/2006 |
Drilled front side skins. |
4.0 |
|
2/7/2006 |
Deburred front skins. Fixed bad rivet in firewall. Riveted and bolted
F-804D. |
2.5 |
2/8/2006 |
Fixed alignment of lower longerons |
1.0 |
|
2/9/2006 |
Set spar distances in fuselage |
1.5 |
2/12/2006 |
Started drilling right center skin |
1.5 |
|
2/13/2006 |
Finished bending and drilling left center skin |
2.0 |
2/14/2006 |
No airplane building. Valentine's day. |
|
|
2/15/2006 |
Bent and drilled and drilled right center skin. Drilled F-805 and F-806
ribs. |
3.0 |
2/16/2006 |
Drilled right rear skin |
2.5 |
|
2/17/2006 |
Drilled left rear skin |
2.0 |
2/19/2006 |
Made rear seat belt attach points |
3.0 |
|
2/20/2006 |
Drilled bottom center and bottom rear skins |
4.0 |
2/21/2006 |
Cut a notch for the tail spring in back bottom skin |
2.0 |
|
2/22/2006 |
Drilled back bottom skin to the skeleton and other skins |
2.5 |
2/23/2006 |
Fabricated landing gear box angle parts |
2.5 |
|
2/24/2006 |
Prepared and primed landing gear box parts |
2.0 |
2/25/2006 |
Built air compressor box |
0 |
|
2/27/2006 |
Added fan to air compressor box |
0 |
2/28/2006 |
Drilled aux longeron and started on landing gear box |
2.0 |
|
3/1/2006 |
Prepared holes in front right F-802A for flush rivets. Then riveted
same. |
2.0 |
3/2/2006 |
Prepared and riveted angles to other F-802A and the two F-802Bs. |
2.0 |
|
3/4/2006 |
Drilled both F-802A to the skins. More horsing around with the air
compressor. |
|
3/5/2006 |
Prepared and drilled bot F-802G to the bottom skin and F-802A. |
1.5 |
|
3/6/2006 |
Started drilling right weldment to ldg gear box |
1.0 |
3/7/2006 |
Finished drilling right weldment. Discovered I had ruined it. |
1.5 |
|
3/8/2006 |
Drilled left WD-822 weldment. |
2.0 |
3/10/2006 |
Finished working on left landing gear box |
3.0 |
|
3/12/2006 |
Drilled right WD-822 weldment (again). |
3.0 |
3/13/2006 |
Finished working on right landing gear box |
3.5 |
|
3/16/2006 |
Countersunk longerons |
1.0 |
3/17/2006 |
Dimpled and deburred rear skin |
2.0 |
|
3/18/2006 |
Primed bottom rear skins. Riveted them into place. Dimpled and deburred
left rear skin. |
5.0 |
3/19/2006 |
Dimpled and deburred right rear skin. Cut vent hole. |
2.5 |
|
3/20/2006 |
Primed rear side skins. Attached rear seat belt anchors. |
2.5 |
3/21/2006 |
Christine and I riveted the right rear skin |
2.5 |
|
3/23/2006 |
We riveted the left rear skin. I prepare then center area for the middle
side skins. |
5.0 |
3/25/2006 |
Prepared middle skins |
1.5 |
|
3/26/2006 |
Riveted right middle skin |
2.5 |
3/27/2006 |
Riveted left middle skin |
2.5 |
|
3/28/2006 |
Replaced bad rivets. |
1.5 |
3/29/2006 |
Prep'ed forward fuselage skeleton. Reflected on dimple directions on
F-822 |
2.0 |
|
3/30/2006 |
Prep'ed F-822 |
3.5 |
4/1/2006 |
Riveted front bottom skin (F-822). Prep'ed bottom middle skins. |
4.0 |
|
4/2/2006 |
Riveted bottom middle skins |
5.5 |
4/3/2006 |
Prepared right front skin. Clecoed into place. |
3.0 |
|
4/6/2006 |
Prepared left front skin |
2.5 |
4/7/2006 |
Riveted right front skin. |
2.5 |
|
4/8/2006 |
Riveted left front skin |
3.0 |
4/9/2006 |
Tipped the canoe! |
3.0 |
|
|
|
|
|
|
|
